High Pressure RX37 API 17D RTJ Ring Joint Gasket
|Carbon Steel||Gasket||Stainless Steel||Seal|
|Metal||Seals Ring||Soft Iron||Gasket|
|Standard||APi 6a||Pressure||High Pressure|
API 17D RTJ Ring Joint Gasket,
RX37 weld ring gasket,
RX37 ring joint flange gasket
The Ring Type Joint Gasket is initially developed for high pressure/ temperature applications found in the petroleum industry and is primarily used in the oilfield on drilling and completion equipment.
However, today this product range can also be found on valves and pipe work assemblies, along with some high integrity pressure vessel joints.
|Gasket type||Ring joint gasket standard||Flange standard|
|Oval||ASME B 16.20 API 6A||ANSI B 16.5 ASME B16.47, SERIES A|
|Octagonal||ASME B 16.20 API 6A||ANSI B 16.5 ASME B16.47, SERIES A|
|RX||ASME B 16.20 API 6A||API 6 B|
|BX||API 6A||API 6 B|
1. Resistance to high temperature and pressure, suitable for high pressure flange
2. Excellent temperature resistance. Permanent temperature range -200℃to +550℃
3. Very high operating pressure limits (320 bar)
4. Good chemical resistance
5. High-grade, reinforced and blow out safe gasket as per UW (Healty and safety at Work Act), high operating safe
6. Very low leakage rate, meets TA-LUFT requirement
7. No ageing, no embitterment, even at high temperature
8. Asbestos-free, physiologically harmless, disposal with domestic waste
9. Good handling during transport, installation and removal. Mechanically stable, scratch-resistant
ASME B16.20 Ring Joint Gaskets, API 6A Ring Joint Gaskets, API 17D Ring Joint Gaskets, Non-standard Ring Joint Gaskets
We can offer more than 30 kinds of materials, such as 321SS, 347SS, 316SS, 304SS, Inconel 625, Monel 400, INCOLY 825, Nickel 200, Duplex F44, soft iron, low carbon steel and so on. We have over 10 years experience in export business. Our products are sold to Southeast Asia, Middle East, Europe and America and well appreciated by our clients.
As a result of metal to metal sealing media they are made to be free of indentations, tool marks etc and have a surface finish of maximum,
· R, RX – 63 microinches Ra (1.6 micrometer Ra).
Thus Gasket supplies ring joint gaskets (RTJ Gasket) with the hardness numbers as follows:
BRINELL HARDNESS NUMBER (max)
ROCKWELL HARDNESS NUMBER (max)
|Low carbon steel||120||68||S|
|4-6% Chrome 1/2% molybdenum||130||72||F5|
|304 Stainless Steel||160||83||S304|
|316 Stainless Steel||160||83||S316|
|347 Stainless Steel||160||83||S347|
|Material||Identification||Material No.||Hardness||Temperature (oC)|
|Low Carbon Steel||S||–||120||-40||500|
|Stainless Steel 304||304SS||1.4301||160||-250||550|
|Stainless Steel 304L||304L SS||1.4306||160||-250||550|
|Stainless Steel 316||316SS||1.4401||160||-100||550|
|Stainless Steel 316L||316L SS||1.4404||160||-100||550|
|Stainless Steel 321||321SS||1.4541||160||-250||550|
|Stainless Steel 347||347SS||1.4450||160||-250||500|
|Stainless Steel 410||410SS||1.4000||170||-20||850|
Marking and Identification (standard):
The outer surface of each Ring Type Joint should show the manufacturer’s name or a trademark, the gasket number like R67, RX37 or BX155, gasket’s material in abbreviation(check below our chart), as well as the standards like ASME B16.20, API 6A, API 17D, etc.
RTJ gaskets are available as standard in soft metal and in 304, 316 and stainless steels. Versions in other materials on request.
Standards and approvals
All RTJ gaskets are manufactured to API standards, guaranteeing consistent quality.
- Oil & gas industry
- Petrochemical industry
- Flange connections
- Pipe connections
Under axial compressive load, ring type joints plastically deform and flow into the irregularities of the flange groove. Since the contact area of the ring type joint is relatively small, a very high compressive load results between the sealing surface of the ring type joint and the flange groove. This surface pressure is further increased especially by the RX and BX RTJ variants. Both variants are able to seal extremely high internal pressures. RTJ gaskets are produced from metal, so they remain in their compressed form, even when the surface pressure is relaxed. The sealing function of the RTJ gasket is reinforced by the axial forces acting on the sealing surfaces.
Forms of supply
- Standard dimensions as per DIN EN 12560-5 or ASME B16.20
- RTJ gaskets are available from stock in ½” to 36” and 15 mm to 900 mm sizes, and in the commonly available materials to suit most ASME and DIN flange dimensions. Larger sizes and special requirements are available to order.
Q: Are you trading company or manufacturer ?
A: We are a professional production enterprise
Q: How long is your delivery time?
A: Generally it is 7-15 days for stock delivery, and 15-30 days for manufacturing goods , but it depands on the quantity.
Q: Do you provide samples ? is it free or extra ?
A: Yes, we can provide you sample, but you need to pay for the sample and freight firstly.We will return the fee after you make an order.
Q: What is your terms of payment ?
A: Payment<=1000USD, 100% in advance. Payment>=1000USD, 30% T/T in advance ,balance before shippment.
Q:How can we trust you to make a guaranteed deal?
A:We can trade through alibaba credit guarantee orders, which will fully guarantee the effective rights and interests of buyers and sellers.
A:For inner box and master carton are made as per international standards,and we can make special designed for you if need.
If you have another question, pls feel free to contact us.